Original Trilogy Bowcaster - Revision history

Gotwookiee at 23:49, 12 September 2021

2021-09-12T23:49:43Z

← Older revision		Revision as of 23:49, 12 September 2021
Line 247:		Line 247:
	#There are two large tapered discs on each side of the bowcaster. They are directly above the trigger and are in exactly the same spot on both sides. These discs are only on the ANH version, not on the Empire/Jedi version. According to kurtyboy, these are both pieces from a JA Michel turntable, either from a sweep arm or stylus brush, and are extremely hard to find.		#There are two large tapered discs on each side of the bowcaster. They are directly above the trigger and are in exactly the same spot on both sides. These discs are only on the ANH version, not on the Empire/Jedi version. According to kurtyboy, these are both pieces from a JA Michel turntable, either from a sweep arm or stylus brush, and are extremely hard to find.
	#The trigger discs are fastened with a #10-32 flat pan head screw.		#The trigger discs are fastened with a #10-32 flat pan head screw.
	#The trigger discs are 25mm in diameter, 3.~~8mm~~ thick at the outer edge, and ~~5.2mm~~ thick in the center.		#The trigger discs are 25mm in diameter, 4.1mm thick at the outer edge, and 6mm thick in the center.

	==== Right Panel====		==== Right Panel====

Gotwookiee at 02:52, 12 September 2021

2021-09-12T02:52:43Z

← Older revision		Revision as of 02:52, 12 September 2021
Line 102:		Line 102:
	#Jason Joiner says there are no markings of any kind that would indicate the make or model of the base crossbow and that the bowcaster had been stripped of its parts, save for the balls at the end of the limbs. The rubber balls are rotting due to their age.		#Jason Joiner says there are no markings of any kind that would indicate the make or model of the base crossbow and that the bowcaster had been stripped of its parts, save for the balls at the end of the limbs. The rubber balls are rotting due to their age.

	====The Horton ~~Magnum and Horton Safari~~ Magnum====		====The Horton Magnum====

	#According to kurtyboy of the RPF, the correct base crossbow is the Horton Magnum, a plastic-coated aluminum crossbow with a 125 lbs. recurve that was produced by Horton Crossbows during the 60's and/or 70's. Only a few fans have managed to acquire the crossbow, and comparisons between it and the photos of the screen used bowcaster prove beyond a doubt that it is the correct crossbow, including the bow prod. They occasionally turn up on [http://www.gunstar.co.uk Gunstar] and sell for anywhere from £120 to £1000. Sometimes the crossbow has a sticker identifying it as a Horton product, but not always. The sticker doesn't list the model name. This makes finding it on auction sites difficult; you have to scan through them and look at the photos.		#According to kurtyboy of the RPF, the correct base crossbow is the Horton Magnum, a plastic-coated aluminum crossbow with a 125 lbs. recurve that was produced by Horton Crossbows during the 60's and/or 70's. Only a few fans have managed to acquire the crossbow, and comparisons between it and the photos of the screen used bowcaster prove beyond a doubt that it is the correct crossbow, including the bow prod. They occasionally turn up on [http://www.gunstar.co.uk Gunstar] and sell for anywhere from £120 to £1000. Sometimes the crossbow has a sticker identifying it as a Horton product, but not always. The sticker doesn't list the model name. This makes finding it on auction sites difficult; you have to scan through them and look at the photos.
			#In May of 2007 I contacted Bernard Horton and referred him to the bowcaster reference images in this guide. He was convinced that the correct crossbow was a skeleton-stocked, military-style crossbow that he made for the SinglePoint Company that was looking for a product to demonstrate their new scope. It was die cast aluminum and nylon coated, and approximately 12,000 to 15,000 were produced in the early to mid 70's.

			==== The Gunmark Crossbow ====

			# Eventually, an offshoot of the SinglePoint Company called Gunmark was founded by Bjorn Waktare (a director of SinglePoint) and sold the Horton Magnum crossbows to civilians, mostly in Europe. The crossbows were simply called "Gunmark Crossbows" according to Mr. Horton, and the company was based in Winchester, UK. [http://www.therpf.com/f9/bowcaster-parts-872/index7.html#post340659 Source 1], [http://www.therpf.com/f9/bowcaster-parts-872/index7.html#post354817 Source 2]

			==== Lillywhites ====

			# [https://www.lillywhites.com/ Lillywhites], a UK sporting goods store, apparently also sold the former Horton Magnum under their own brand as well. [https://www.therpf.com/forums/members/papermaker.211561/ Papermaker] apparently found one several years back. He speculates that the Horton Magnum did not sell particularly well when introduced, and ended up being wholesaled to any number of smaller retailers, who branded it as their own.

			==== The Horton Safari Magnum ====
	#In 2005 the Horton Safari Magnum was discovered by members of the RPF and has since become a common crossbow for conversions. It is the correct size and shape, but it made of plastic and has a solid stock. It is commonly available on eBay for ~$150.		#In 2005 the Horton Safari Magnum was discovered by members of the RPF and has since become a common crossbow for conversions. It is the correct size and shape, but it made of plastic and has a solid stock. It is commonly available on eBay for ~$150.

	====The Horton Monarch Supreme ~~and the Gunmark Crossbow~~====		====The Horton Monarch Supreme====

	#The Horton Safari Magnum is so close to the bowcaster that many became convinced that the bowcaster was built on an earlier Horton Crossbow. After looking at pictures of the bowcaster, Michelle at Horton Crossbows is 95% sure that the bowcaster was a Horton based on certain signature details that are common to Horton crossbows.		#The Horton Safari Magnum is so close to the bowcaster that many became convinced that the bowcaster was built on an earlier Horton Crossbow. After looking at pictures of the bowcaster, Michelle at Horton Crossbows is 95% sure that the bowcaster was a Horton based on certain signature details that are common to Horton crossbows.
	#This prompted kurtyboy to contact Horton USA who said that the base crossbow was definitely a very old Horton that was a predecessor to the Safari Magnum. It had an aluminum frame and Horton USA was only in possession of one at the time kurtyboy contacted them and it was not for sale.		#This prompted kurtyboy to contact Horton USA who said that the base crossbow was definitely a very old Horton that was a predecessor to the Safari Magnum. It had an aluminum frame and Horton USA was only in possession of one at the time kurtyboy contacted them and it was not for sale.
	#I followed up on this by asking Horton what model crossbow they were referring to, and my message was forwarded to Bernard Horton himself who said it was called the Horton Monarch Supreme and was made in the late 60's and early 70's in Wales. Only about 3,000 were ever produced.		#I followed up on this by asking Horton what model crossbow they were referring to, and my message was forwarded to Bernard Horton himself who said it was called the Horton Monarch Supreme and was made in the late 60's and early 70's in Wales. Only about 3,000 were ever produced.
	#However, in May of 2007 I contacted Mr. Horton again and referred him to the bowcaster reference images in this guide. He was convinced that the correct crossbow is not the Monarch Supreme but a skeleton-stocked, military-style crossbow that he made for the SinglePoint Company that was looking for a product to demonstrate their new scope. It was die cast aluminum and nylon coated, and approximately 12,000 to 15,000 were produced in the early to mid 70's. Eventually, an offshoot of the SinglePoint Company called Gunmark was founded by Bjorn Waktare (a director of SinglePoint) and sold these crossbows to civilians, mostly in Europe. The crossbows were simply called "Gunmark Crossbows" according to Mr. Horton, and the company was based in Winchester, UK. [http://www.therpf.com/f9/bowcaster-parts-872/index7.html#post340659 Source 1], [http://www.therpf.com/f9/bowcaster-parts-872/index7.html#post354817 Source 2]		#However, in May of 2007 I contacted Mr. Horton again and referred him to the bowcaster reference images in this guide. He was convinced that the correct crossbow is not the Monarch Supreme but a skeleton-stocked, military-style crossbow that he made for the SinglePoint Company that was looking for a product to demonstrate their new scope.

	====The Barnett Commando ~~Crossbow and the infamous Champagne Champion~~ Crossbow====		====The Barnett Commando Crossbow====

	#Before the discovery of the Horton Magnum and Magnum Safari crossbows, the Barnett Commando Crossbow was a popular base for bowcaster replicas. Randy5000 claimed he had a “secret contact” at Lucasfilm that told him the Bowcaster was based on a Barnett Commando Crossbow. While close, numerous fans, including kurtyboy, have determined that the Barnett is too large.		#Before the discovery of the Horton Magnum and Magnum Safari crossbows, the Barnett Commando Crossbow was a popular base for bowcaster replicas. Randy5000 claimed he had a “secret contact” at Lucasfilm that told him the Bowcaster was based on a Barnett Commando Crossbow. While close, numerous fans, including kurtyboy, have determined that the Barnett is too large.
			#The Barnett was later used as the base crossbow for the [[Sequel Trilogy Bowcaster]].

			==== The Champagne Champion Crossbow ====
	#For years it was commonly claimed that the base crossbow was the "Champagne Champion Crossbow." In 2005, Macklin claimed that the source of the information was Jeff Ritzmann, a prop/costume guy and 501st member, with whom he spoke in 1999. According to Macklin, Mr. Ritzmann claimed to have done some research and not only discovered the basis of the crossbow, but also found one. However, over the years no one has found any evidence to support the existence of the Champagne Champion Crossbow or the company that made it. Macklin says that Ritzmann said it was "ultra rare."		#For years it was commonly claimed that the base crossbow was the "Champagne Champion Crossbow." In 2005, Macklin claimed that the source of the information was Jeff Ritzmann, a prop/costume guy and 501st member, with whom he spoke in 1999. According to Macklin, Mr. Ritzmann claimed to have done some research and not only discovered the basis of the crossbow, but also found one. However, over the years no one has found any evidence to support the existence of the Champagne Champion Crossbow or the company that made it. Macklin says that Ritzmann said it was "ultra rare."
			#[https://www.therpf.com/forums/members/papermaker.211561/ Papermaker] speculates that the Horton Magnum did not sell particularly well when introduced, and ended up being wholesaled to any number of smaller retailers, who branded it as their own. Champagne may have been one such brand.

	=== Scopes===		=== Scopes===

Gotwookiee at 03:14, 9 September 2021

2021-09-09T03:14:03Z

← Older revision		Revision as of 03:14, 9 September 2021
Line 90:		Line 90:
	===[https://www.youtube.com/watch?v=wJDAmBQ1u2g The Star Wars Holiday Special]===		===[https://www.youtube.com/watch?v=wJDAmBQ1u2g The Star Wars Holiday Special]===

	~~==General~~ Information==		{{Reference Information\|item=prop}}
			A set of detailed notes researching the original {{{item\|prop or costume}}}.
	Like many props, the original trilogy bowcasters were built from vintage firearms rented from [http://www.bapty.co.uk Bapty & Company] in the UK.		Like many props, the original trilogy bowcasters were built from vintage firearms rented from [http://www.bapty.co.uk Bapty & Company] in the UK.

Line 263:		Line 264:
	#According to trooper, the large coiled cord that runs around back of the scopes is an old headphone cord. The cable is 4.5mm in diameter and the coil is 14mm in diameter. Post in thread 'cancelled, Star wars anh chewbacca bowcaster run' <nowiki>https://www.therpf.com/forums/threads/cancelled-star-wars-anh-chewbacca-bowcaster-run.288779/post-4550629</nowiki>		#According to trooper, the large coiled cord that runs around back of the scopes is an old headphone cord. The cable is 4.5mm in diameter and the coil is 14mm in diameter. Post in thread 'cancelled, Star wars anh chewbacca bowcaster run' <nowiki>https://www.therpf.com/forums/threads/cancelled-star-wars-anh-chewbacca-bowcaster-run.288779/post-4550629</nowiki>

	=~~=Materials & Construction Techniques==~~		{{Tutorials and Resources\|item= bowcaster}}

	===Scratch/Hardware Builds ===		===Scratch/Hardware Builds ===
Line 283:		Line 284:

	#[https://www.thingiverse.com/thing:2402724 Thingverse: Single Point Scope.]		#[https://www.thingiverse.com/thing:2402724 Thingverse: Single Point Scope.]

			{{Community\|item= the bowcaster}}

Gotwookiee at 02:56, 9 September 2021

2021-09-09T02:56:08Z

← Older revision		Revision as of 02:56, 9 September 2021
Line 6:		Line 6:
	[[Category:Chewbacca]]		[[Category:Chewbacca]]
	Chewbacca's signature weapon, used throughout the original ''Star Wars'' trilogy and the infamous ''Holiday Special''.		Chewbacca's signature weapon, used throughout the original ''Star Wars'' trilogy and the infamous ''Holiday Special''.
	==Reference ~~Images=~~=		{{Reference Media\|item=prop}}

	===Pre-Production===		===Pre-Production===

172.58.190.180: /* Coiled Cords */

2021-06-06T20:17:20Z

Coiled Cords

← Older revision		Revision as of 20:17, 6 June 2021
Line 161:		Line 161:

	# According to Macklin, the barrel is 5/8 inches in diameter.		# According to Macklin, the barrel is 5/8 inches in diameter.
			# kurtyboy’s scaling work reveals a 310mm barrel length (plus whatever is in the barrel mount block), with 1/16” thick tubing. Post in thread 'cancelled, Star wars anh chewbacca bowcaster run' <nowiki>https://www.therpf.com/forums/threads/cancelled-star-wars-anh-chewbacca-bowcaster-run.288779/post-4523309</nowiki>

	=== Barrel Mount Block ===		=== Barrel Mount Block ===
Line 249:		Line 250:
	====Left Panel ====		====Left Panel ====

	#The knurled knob near the front of the panel is from a Zorki 35mm film camera.		#The knurled knob near the front of the panel is from a Zorki 1 35mm film camera.
	#The 3 notched discs are the same discs found on the Imperial officer hats, various belt buckles, and other props and costume pieces. They are parts from 70's era J.A. Michel record turntables.		#The 3 notched discs are the same discs found on the Imperial officer hats, various belt buckles, and other props and costume pieces. They are parts from 70's era J.A. Michel record turntables.
	#The large knob at the top back end of the panel is a vintage [http://www.tubesandmore.com/products/P-K314-1 Fender "witches hat" knob].		#The large knob at the top back end of the panel is a vintage [http://www.tubesandmore.com/products/P-K314-1 Fender "witches hat" knob].
	#The fat skirted knob with the hole in the center, located near the middle of the panel, is made up of parts from two different 35mm film cameras. The skirt is from a Zorki 1 35mm camera. There are several variants of this skirt, but you want the one that counts clockwise with a a rivet between the numbers 5 and 10. The knob itself is a diamond knurled film winding knob from a vintage Kodak 35mm camera. There are many variants that don't have the correct knob.		#The fat skirted knob with the hole in the center, located near the middle of the panel, is made up of parts from two different 35mm film cameras. The skirt is from a Zorki 1 35mm camera. There are several variants of this skirt, but you want the one that counts clockwise with a a rivet between the numbers 5 and 10. The knob itself is a diamond knurled film winding knob from a vintage Kodak rf 35mm camera. There are many variants that don't have the correct knob.

	===Coiled Cords===		===Coiled Cords===
Line 260:		Line 261:
	# On the ANH bowcaster, the right side coiled cord is smaller than the other one. On the TESB/ROTJ bowcaster, it is the same size.		# On the ANH bowcaster, the right side coiled cord is smaller than the other one. On the TESB/ROTJ bowcaster, it is the same size.
	#The [http://www.partsofsw.com/bowcast.htm Parts of SW Bowcaster Page] claims that it is a Graflex flash cord, however Boba Debt believes that people say Graflex simply because it is common knowledge that the prop builders on the films used Graflex flash tubes for Luke's lightsabres. It could be any type of black coiled cord.		#The [http://www.partsofsw.com/bowcast.htm Parts of SW Bowcaster Page] claims that it is a Graflex flash cord, however Boba Debt believes that people say Graflex simply because it is common knowledge that the prop builders on the films used Graflex flash tubes for Luke's lightsabres. It could be any type of black coiled cord.
			#According to trooper, the large coiled cord that runs around back of the scopes is an old headphone cord. The cable is 4.5mm in diameter and the coil is 14mm in diameter. Post in thread 'cancelled, Star wars anh chewbacca bowcaster run' <nowiki>https://www.therpf.com/forums/threads/cancelled-star-wars-anh-chewbacca-bowcaster-run.288779/post-4550629</nowiki>

	==Materials & Construction Techniques==		==Materials & Construction Techniques==

Gotwookiee: /* Knobs, Dials, & Discs */

2021-05-28T21:55:58Z

Knobs, Dials, & Discs

← Older revision		Revision as of 21:55, 28 May 2021
Line 226:		Line 226:
	#All information on the discs and dials on the side panels are based on the ANH bowcaster. In all photos of the Empire/Jedi bowcaster, the sides are obscured by Chewie's hair.		#All information on the discs and dials on the side panels are based on the ANH bowcaster. In all photos of the Empire/Jedi bowcaster, the sides are obscured by Chewie's hair.
	#All discs and dials are held in place with a flat pan head screw with a diameter of 7mm.		#All discs and dials are held in place with a flat pan head screw with a diameter of 7mm.
	#There are two large discs ~~with a small bump in the center~~ on each side of the bowcaster. They are directly above the trigger and are in exactly the same spot on both sides. These discs are only on the ANH version, not on the Empire/Jedi version. According to kurtyboy, these are both pieces from a JA Michel turntable, either from a sweep arm or stylus brush, and are extremely hard to find.
	#~~lonepigeon has done some scaling work and has determined that the disc above the~~ trigger ~~on each side is about 1~~.~~125"~~ in diameter. ~~The two by~~ the ~~big knob on~~ the ~~right side should be 1" (assuming the big knob is the same as the one found at 1.46")~~.		==== Trigger Discs ====
			#There are two large tapered discs on each side of the bowcaster. They are directly above the trigger and are in exactly the same spot on both sides. These discs are only on the ANH version, not on the Empire/Jedi version. According to kurtyboy, these are both pieces from a JA Michel turntable, either from a sweep arm or stylus brush, and are extremely hard to find.
			#The trigger discs are fastened with a #10-32 flat pan head screw.
			#The trigger discs are 25mm in diameter, 3.8mm thick at the outer edge, and 5.2mm thick in the center.

	==== Right Panel====		==== Right Panel====

Gotwookiee: /* Star Wars Behind the Scenes */

2021-03-15T06:06:30Z

Star Wars Behind the Scenes

← Older revision		Revision as of 06:06, 15 March 2021
Line 37:		Line 37:
	File:Otbowcaster anhbts 004.jpg\|alt=A behind the scenes photo of the bowcaster from the production of the original Star Wars.		File:Otbowcaster anhbts 004.jpg\|alt=A behind the scenes photo of the bowcaster from the production of the original Star Wars.
	File:Otbowcaster anhbts 005.jpg\|alt=A behind the scenes photo of the bowcaster from the production of the original Star Wars.		File:Otbowcaster anhbts 005.jpg\|alt=A behind the scenes photo of the bowcaster from the production of the original Star Wars.
			File:Otbowcaster anhbts 006.jpg\|alt=A behind the scenes photo of the bowcaster from the production of the original Star Wars.
			File:Otbowcaster anhbts 007.jpg\|alt=A behind the scenes photo of the bowcaster from the production of the original Star Wars.
			File:Otbowcaster anhbts 008.jpg\|alt=A behind the scenes photo of the bowcaster from the production of the original Star Wars.
	</gallery>		</gallery>

Line 60:		Line 63:
	File:Otbowcaster rotj 012.jpg\|alt=A screenshot of the bowcaster from Return of the Jedi.		File:Otbowcaster rotj 012.jpg\|alt=A screenshot of the bowcaster from Return of the Jedi.
	File:Otbowcaster rotj 013.jpg\|alt=A screenshot of the bowcaster from Return of the Jedi.		File:Otbowcaster rotj 013.jpg\|alt=A screenshot of the bowcaster from Return of the Jedi.
			File:Otbowcaster rotj 014.jpg\|alt=A screenshot of the bowcaster from Return of the Jedi.
	</gallery>		</gallery>

Line 74:		Line 78:
	File:Otbowcaster bts 004.jpg\|alt=A publicity shot of the bowcaster from Empire/Jedi era.		File:Otbowcaster bts 004.jpg\|alt=A publicity shot of the bowcaster from Empire/Jedi era.
	File:Otbowcaster bts 005.jpg\|alt=A publicity shot of the bowcaster from Empire/Jedi era.		File:Otbowcaster bts 005.jpg\|alt=A publicity shot of the bowcaster from Empire/Jedi era.
			File:Otbowcaster bts 006.jpg\|alt=A publicity shot of the bowcaster from Empire/Jedi era.
	</gallery>		</gallery>

Gotwookiee: /* General Information */

2021-02-19T04:31:40Z

General Information

← Older revision		Revision as of 04:31, 19 February 2021
Line 87:		Line 87:
	==General Information==		==General Information==
	Like many props, the original trilogy bowcasters were built from vintage firearms rented from [http://www.bapty.co.uk Bapty & Company] in the UK.		Like many props, the original trilogy bowcasters were built from vintage firearms rented from [http://www.bapty.co.uk Bapty & Company] in the UK.

			[https://www.therpf.com/forums/threads/anh-esb-bowcaster.333128/ ANH/TESB Differences]

	===The Crossbow===		===The Crossbow===

Gotwookiee: /* The Crossbow */

2021-01-21T02:30:33Z

The Crossbow

← Older revision		Revision as of 02:30, 21 January 2021
Line 151:		Line 151:
	#The bowstring is also present during the bowcaster's brief appearance in the Star Wars Holiday Special.		#The bowstring is also present during the bowcaster's brief appearance in the Star Wars Holiday Special.

	===Barrel ~~Assembly~~===		===Barrel===

			# According to Macklin, the barrel is 5/8 inches in diameter.

			=== Barrel Mount Block ===

			# There is a block underneath the scopes that the rear of the barrel mounts to.
			# odiwan72 has suggested that the barrel, barrel mount block and the barrel support resemble a crossbow "goat's foot" cocking lever, similar to a Barnett "Goat's Foot" cocking lever. It makes sense that the cocking lever, an essential piece of crossbow hardware, would have come into Bapty's possession together and would have been used. If it is a cocking lever, it is likely of Horton manufacture.

			=== Barrel Brackets ===

			==== A New Hope version ====

			# The base of the barrel is attached to a Y-shaped lever of some kind that attaches to the scope mount. It appears to be about 1/4" thick and made of metal.

			==== Empire Strikes Back/Return of the Jedi version ====

			# There are no lever shaped pieces surrounding the scope mounts on the Empire/Jedi version; the barrel just ends underneath the single point scope.

			=== Barrel Support ===

	====A New Hope version====		====A New Hope version====

	~~# According to Macklin, the barrel is .625 inches in diameter, and the bowcaster itself is 27½ inches long.~~		# On the ANH bowcaster, there is a long metal piece that the barrel goes through behind the front sight, with another barrel-sized hole directly beneath it. The bottom of this piece appears to have a hinge of some kind. I have dubbed this piece the barrel support. This piece is much wider at the base/hinge and gets narrow towards the top where the barrel goes through.
	#On the ANH bowcaster, there is a long metal piece that the barrel goes through behind the front sight, with another barrel-sized hole directly beneath it. The bottom of this piece appears to have a hinge of some kind. I have dubbed this piece the barrel support. This piece is much wider at the base/hinge and gets narrow towards the top where the barrel goes through.
	~~#The base of the barrel is attached to a Y-shaped lever of some kind that attaches to the scope mount. It appears to be about 1/4" thick and made of metal.~~
	#odiwan72 has suggested that the barrel, barrel box and the barrel support resemble a crossbow "goat's foot" cocking lever, similar to a Barnett "Goat's Foot" cocking lever. It makes sense that the cocking lever, an essential piece of crossbow hardware, would have come into Bapty's possession together and would have been used. If it is a cocking lever, it is likely of Horton manufacture.

	====Empire Strikes Back/Return of the Jedi version====		====Empire Strikes Back/Return of the Jedi version====

	#On the TESB/ROTJ bowcaster, the barrel support has a more consistent width than the ANH version. There is still a hinge of some kind at the base. The hole is much lower; closer to the hinge than the ANH barrel support. It also looks to be smaller than the hole the barrel goes through.		#On the TESB/ROTJ bowcaster, the barrel support has a more consistent width than the ANH version. There is still a hinge of some kind at the base. The hole is much lower; closer to the hinge than the ANH barrel support. It also looks to be smaller than the hole the barrel goes through.
	~~#There are no lever shaped pieces surrounding the scope mounts on the Empire/Jedi version; the barrel just ends underneath the single point scope.~~

	=== Front Sight===		=== Front Sight Guard===

	====A New Hope version====		====A New Hope version====
	[[File:Bowcaster anh sight-guard.png\|alt=Collage of images of the front sight guard on the ANH bowcaster\|none\|thumb]]		[[File:Bowcaster anh sight-guard.png\|alt=Collage of images of the front sight guard on the ANH bowcaster\|none\|thumb]]
			#As of January 2021, the original source item for this part has not been identified.
			#The part resembles the sight protectors/sight guards of various World War II European rifles.
	#According to Ripcode of The Dented Helmet, the front sight on the bowcaster is an Enfield No. 4's sight protector. ([http://www.therpf.com/f9/bowcaster-parts-872/index5.html#post123691 Source]) However, both GotWookiee and lonepigeon have found these for sale, and while they look close, they are not a match. [http://www.therpf.com/f9/bowcaster-parts-872/index5.html#post123840 Source]		#According to Ripcode of The Dented Helmet, the front sight on the bowcaster is an Enfield No. 4's sight protector. ([http://www.therpf.com/f9/bowcaster-parts-872/index5.html#post123691 Source]) However, both GotWookiee and lonepigeon have found these for sale, and while they look close, they are not a match. [http://www.therpf.com/f9/bowcaster-parts-872/index5.html#post123840 Source]
	#The ANH sight looks somewhat similar to an Enfield sight; it has a flat top and a split in the center. Two bent arms or wings are attached to it.		#The ANH sight looks somewhat similar to an Enfield sight; it has a flat top and a split in the center. Two bent arms or wings are attached to it.
	#Datsun ~~hose clamp~~		#A Datsun swaybar bushing has been put forward as a possible candidate, with the "ears" being bolted on by the production crew.

	====Empire Strikes Back/Return of the Jedi version====		====Empire Strikes Back/Return of the Jedi version====

	#The TESB/ROTJ ~~sight~~ is different; it is solid and round with no split or flat top. The arms/wings appear to be straight. They also appear to be part of the sight, rather than bolted on like the ANH version.		#The TESB/ROTJ slightly is different; it is solid and round with no split or flat top. The arms/wings appear to be straight. They also appear to be part of the sight, rather than bolted on like the ANH version.

	===Balls ===		===Balls ===
Line 191:		Line 208:
	#The ANH sling appears to be wider than the thickness of the bowcaster body, probably about 2” wide.		#The ANH sling appears to be wider than the thickness of the bowcaster body, probably about 2” wide.
	#According to TK818, the ANH Bowcaster used a 2 inch wide nylon medical bag strap, the same as the Aliens Pulse Rifle.		#According to TK818, the ANH Bowcaster used a 2 inch wide nylon medical bag strap, the same as the Aliens Pulse Rifle.
			#The correct sling is a British MKVI Gasmask Bag Neck Strap.

	====Empire Strikes Back/Return of the Jedi version====		====Empire Strikes Back/Return of the Jedi version====

Gotwookiee: /* Front Sight */

2021-01-07T05:39:15Z

Front Sight

← Older revision		Revision as of 05:39, 7 January 2021
Line 168:		Line 168:

	====A New Hope version====		====A New Hope version====
			[[File:Bowcaster anh sight-guard.png\|alt=Collage of images of the front sight guard on the ANH bowcaster\|none\|thumb]]
	#According to Ripcode of The Dented Helmet, the front sight on the bowcaster is an Enfield No. 4's sight protector. ([http://www.therpf.com/f9/bowcaster-parts-872/index5.html#post123691 Source]) However, both GotWookiee and lonepigeon have found these for sale, and while they look close, they are not a match. [http://www.therpf.com/f9/bowcaster-parts-872/index5.html#post123840 Source]		#According to Ripcode of The Dented Helmet, the front sight on the bowcaster is an Enfield No. 4's sight protector. ([http://www.therpf.com/f9/bowcaster-parts-872/index5.html#post123691 Source]) However, both GotWookiee and lonepigeon have found these for sale, and while they look close, they are not a match. [http://www.therpf.com/f9/bowcaster-parts-872/index5.html#post123840 Source]
	#The ANH sight looks somewhat similar to an Enfield sight; it has a flat top and a split in the center. Two bent arms or wings are attached to it.		#The ANH sight looks somewhat similar to an Enfield sight; it has a flat top and a split in the center. Two bent arms or wings are attached to it.

← Older revision		Revision as of 06:06, 15 March 2021
Line 37:		Line 37:
	File:Otbowcaster anhbts 004.jpg\|alt=A behind the scenes photo of the bowcaster from the production of the original Star Wars.		File:Otbowcaster anhbts 004.jpg\|alt=A behind the scenes photo of the bowcaster from the production of the original Star Wars.
	File:Otbowcaster anhbts 005.jpg\|alt=A behind the scenes photo of the bowcaster from the production of the original Star Wars.		File:Otbowcaster anhbts 005.jpg\|alt=A behind the scenes photo of the bowcaster from the production of the original Star Wars.
			File:Otbowcaster anhbts 006.jpg\|alt=A behind the scenes photo of the bowcaster from the production of the original Star Wars.
			File:Otbowcaster anhbts 007.jpg\|alt=A behind the scenes photo of the bowcaster from the production of the original Star Wars.
			File:Otbowcaster anhbts 008.jpg\|alt=A behind the scenes photo of the bowcaster from the production of the original Star Wars.
	</gallery>		</gallery>

Line 60:		Line 63:
	File:Otbowcaster rotj 012.jpg\|alt=A screenshot of the bowcaster from Return of the Jedi.		File:Otbowcaster rotj 012.jpg\|alt=A screenshot of the bowcaster from Return of the Jedi.
	File:Otbowcaster rotj 013.jpg\|alt=A screenshot of the bowcaster from Return of the Jedi.		File:Otbowcaster rotj 013.jpg\|alt=A screenshot of the bowcaster from Return of the Jedi.
			File:Otbowcaster rotj 014.jpg\|alt=A screenshot of the bowcaster from Return of the Jedi.
	</gallery>		</gallery>

Line 74:		Line 78:
	File:Otbowcaster bts 004.jpg\|alt=A publicity shot of the bowcaster from Empire/Jedi era.		File:Otbowcaster bts 004.jpg\|alt=A publicity shot of the bowcaster from Empire/Jedi era.
	File:Otbowcaster bts 005.jpg\|alt=A publicity shot of the bowcaster from Empire/Jedi era.		File:Otbowcaster bts 005.jpg\|alt=A publicity shot of the bowcaster from Empire/Jedi era.
			File:Otbowcaster bts 006.jpg\|alt=A publicity shot of the bowcaster from Empire/Jedi era.
	</gallery>		</gallery>